CPK表格式

零件名称/编号PartName/No.:YL-G530091工序名称/编号ProcessName/No.:数控整体精车，钻中心孔工程规范EngnieeringSpecification:φ10.2±0.1设备名称/编号Equipment/No.:数控车床生产部门/操作者ProductionDept./Operator:样本容量/频率SampleSize/Frequency:125/2h12345678910111213141516171819202122232425110.2410.210.1910.1710.210.1910.1810.210.210.1610.1710.2210.1910.1810.210.210.2110.210.1810.210.210.210.2110.2210.2210.210.210.210.210.210.1810.210.1610.2310.210.1610.210.210.1710.2410.210.210.210.210.2310.2310.210.210.2210.2310.210.210.2310.210.210.2310.210.2110.2510.210.1710.2210.210.2110.210.1810.1610.210.210.1910.2110.1710.210.210.2410.2110.210.2210.2310.2110.1910.210.1810.210.2110.210.2110.2110.210.2210.1910.2110.2110.1710.2410.2110.1510.210.2210.22510.2310.1610.2110.2110.210.210.1910.1610.210.210.1810.2310.210.2210.2210.210.1910.210.2210.210.2410.1910.210.210.1910.21610.19210.21010.20210.20210.19810.19410.18210.21610.19410.17610.21610.20010.19610.21610.19410.19410.20210.19410.21210.21810.18210.20210.21210.2020.0400.0400.0400.0600.0100.0500.0200.0500.0500.0500.0400.0300.0200.0500.0400.0200.0500.0100.0500.0500.0400.0500.0100.0200.030XbarChart*规格下限/LSL=RChart报告编号:RecordNo.:0.078Rbar=0.037日期Date时间Time绍兴XXXX机械有限公司2.1112.129初始过程PPK稳定过程CPK过程能力研究报告ProcessCapabilityStudyReportLCL-xbar=10.180UCLR=1.80910.100UCL-xbar=10.2222.091.78实测值ActualValueXbar=R(Max-Min)=Xdoublebar=10.2011.777*规格上限/USL=10.30.0190.0162.092CPK=Min(CPU,CPL)=完成者/日期：施建欢CompletedBy/Date:记录人/日期：施建欢RecordedBy/Date:*初始过程能力研究中，样本为连续取样，按时间顺序分别记录测量数据Pleasesamplingthedatacontinualinprocesscapabilitystudy,andrecordthedatabytimesequence!*过程能力研究(针对稳定过程)，样本为间隔取样，按规定的时间间隔，每次连续取样5PCS，并按顺序记录测量数据。Pleasesampling5PCSpartsonetimepersettledtime,andrecordthedatabytimesequence!1.793PPK=Min(PPU,PPL)=10.15010.16010.17010.18010.19010.20010.21010.22010.2300.0000.0100.0200.0300.0400.0500.0600.0700.0800.09012345678910111213141516171819202122232425=?--==niiSnxx11)(?2s=-=SpLSLUSLPs6=-=sXUSLPpus?3=-=sLSLXPpLs?3==dR2s=-=s6LSLUSLCp=-=s3XUSLCpu=-=s3LSLXCpL均值控制中限：123456789101112131415161718192021222324251`2345XdoubleBar=LCL-xbar=UCLR=Rbar=*对出现奇异点的情况，分析原因，并调整。Ifappearabnormalpoint(s),Pleaseanalysisthecauseandadjustit.φ10.2±0.1生产部门/操作者:ProductionDept./Operator:0YorCompanyLogoXbar-R控制图ShewhartControlChart记录编号:RecordNo.:零件名称/编号:PartName/No.:YL-G530091工序名称/编号:ProcessName/No.:数控整体精车，钻中心孔工程规范:EngineeringSpecification:Xbar=R(Max-Min)=UCL-xbar=10.222样本容量/频率:SampleSize/Frequency:125/2h日期Date实测值ActualValue设备名称/编号:Equipment/No.:0.037数控车床XbarChartRChart10.20110.1800.07810.15010.16010.17010.18010.19010.20010.21010.22010.2300.0000.0100.0200.0300.0400.0500.0600.0700.0800.09012345678910111213141516171819202122232425